News & Events


Home News & Events
Health & Safety
/ Categories: News

Top tips to prepare your machine for winter

Although most modern construction equipment is built to operate in the toughest of conditions, a few simple procedures will keep your machines running at their best. Here are some top tips for winterizing your construction equipment and keep them in great operating condition during the winter months.

1. Install the correct lubricants and condition hydraulic hoses

Before it gets too cold outside, install the correct engine, hydraulic, transmission and final drive lubricants for your exact machine. Before starting the machine, check each level to ensure they are fluid enough for proper flow. To do so, check each dipstick and, if the oil drips, then it is fluid enough. NEVER use oil that has been diluted with kerosene.

Additionally, the outer wrapper of hydraulic hoses can crack when flexed in colder temperatures. The hoses will still function properly and carry oil at the expected pressure, but to avoid having the hoses crack, condition them before the temperatures drop. To do so, operate your machine so that the hydraulic oil temperature reaches 150 and continue running it for an hour. For best results, apply an arctic hydraulic oil for colder months and normal machine use will condition the hydraulic hoses.

2. Store equipment safely

When your machine is not being used, it’s best to keep it out of the elements if possible for an easier start. If your machine is off the clock during the winter months, make sure you detach any attachments and store them away separately to avoid damage to hinges and joints.

Always keep fluids and oils in room temperature to avoid freezing. If the machine uses diesel exhaust fluid, or DEF, it’s important for operators to know that it can freeze and thaw without hurting its ability to function properly. DEF has a shelf life of one year but varies depending on storage conditions. If owners aren't going to use their equipment during the winter, it's a good idea to store indoors in temperature-controlled environments that are out of direct sunlight.

3. Tyre and Fuel Protection

Fuel and proper tyre pressure are two important components that should be checked before and during the winter season. Tyres should be checked for the proper tyre pressure and look for wear marks on the tyre. Low temperatures will reduce the tyre pressure so if you have the option, consider using track mounted equipment instead of tire-mounted equipment.

Fuel tanks should be maintained full, to prevent condensation inside the tank and along the fuel lines. You can use a fuel treatment that can be added to diesel or fuel tanks that will thaw frozen fuel filters, liquefy fuel and remove moisture from the lines and tank.

4. Keep batteries fully charged and warm

Cold weather requires your batteries to generate nearly twice as many cranking amps in order to turn over, so keep yours charged and warm for easy starting. If you are working in subzero temperatures, storing the battery indoors at room temperature could help when it’s not in use.

5. Warm up Engine

Help prevent the intake and exhaust valves from sticking by running your engine before you begin each day’s work until it reaches operating temperature. Additionally, give your machine a nice stretch and cycle through all of the machine’s functions to distribute warmed oil until they all operate with ease.

6. Conduct a visual inspection

The easiest way to check if your electrical wiring, attachments and hoses are wearing or being damaged is to take a look at each, and all of your components, before daily operation. Look for cracks, cuts and worn spots on all hydraulic hoses, belts and tires. Also, remove any snow/ice, dirt, and debris from tires or undercarriages. Before the winter, schedule an undercarriage inspection with your local Pat O’Donnell & Co. Service department.

Additional Helpful Tips

There are other areas that you need to be aware of and be sure they are checked before the winter season:

·         Grease Points - Properly grease all areas to prevent moisture from building up. Remember to use low-temp lube as recommended by manufacturers.

·         DEF - Newer equipment uses DEF, diesel exhaust fluid, but this one will freeze at 10 degrees or below. Make sure that there is a way to heat and thaw frozen DEF to keep your equipment running.

·         Undercarriage - Remove any excess of snow or debris below as it will increase the operating costs of your equipment.

·         Batteries - Avoid charging a frozen battery as it will normally explode. If the battery is not being used for extended period of time, then you will need to maintain the battery connected to prevent it from drain completely.

With the winter months quickly approaching, contractors and business owners have to start thinking about preparing their equipment for harsh winter weather conditions.

Whether working in the freezing temperatures or storing equipment for the season, companies need to ensure proper winter maintenance to avoid costly problems come spring.

Engine Maintenance

When it comes to a machine’s engine, it’s important for operators to pay close attention to fuel, lubrication and air filtration. Failure to do so could result in costly repairs or machine downtime.

Fuel system maintenance includes cleaning the fuel tank cap/vent and making sure the cap is functioning properly; checking for water or sediment in the fuel, which is the number one cause of fuel injection system failures; and inspecting the fuel filter.

Also, verify the quality of fuel you are using/receiving from your provider. Cold weather operation tends to accentuate any fuel quality issues, such as moisture in the fuel or contaminants.

Engine oils protect the engine’s vital engine components. Make sure to always follow the equipment manufacturer’s lubricant and change interval recommendations. Inspect the air filtration system for any openings that could draw in unfiltered air and always use the correct replacement filter. Contaminated air is a common cause of premature engine failure.

Also, make sure to store DEF in an HTPE plastic or stainless steel container, as it is mildly corrosive. DEF can be filled up prior to storage, however, make sure to leave room for expansion. DEF can expand in the winter up to 7 percent and potentially crack the reservoir.

Protecting Cooling Systems

Cooling systems should be inspected regularly, including the coolant reservoir and hoses. Contractors should verify that coolant in the radiator is always filled to the cap, and also inspect the cap for proper relief pressure.

Coolant does more than just keep the cooling system from freezing. It prevents corrosion, lubricates shaft seals, increases the boiling point temperature and inhibits cavitation, which is a damaging condition that erodes components. Because of this, coolants should be flushed and replaced at OEM-specified intervals. Contractors should also check the coolant concentration, which should be maintained at 50 percent. Pay attention to whether the system uses conventional or OAT coolants and never mix the two. 

Maximizing Your Batteries

Preventative winter maintenance of the battery actually starts in the fall. There are a number of steps operators should take to start preparing their equipment for the cold winter months.

For starters, check that the battery electrolyte is up to the full indicator ring and over the top of the plates. Plates that have dried will never perform satisfactorily again. It’s also good practice to check the rated current output of the alternator and load test current output of the battery.

Operators should clean any dirt and debris from the top of the battery; it can create a conductive path and slowly drain energy. If there’s any corrosion around the posts, clean them using a little baking soda and a terminal brush. The main point here is that you want to ensure the terminal posts and cables have clean and secure contact, ensuring the best and most consistent current supply from the batteries to the machine.

If the machine isn’t going to be used for the winter and will be stored outdoors, it’s best to remove the batteries and store them indoors to prevent freezing. Anytime a battery will be sitting for an extended period, it is best to connect it to a battery maintainer to keep them at a full state of charge. This will keep them ready when the time comes to use the machine.

Contrary to belief, cold temperatures don’t significantly impact the service life of a battery. However, it does induce a “stress test”, amplifying the effects of time, heat, vibration and performance of the charging system. If the machine will be operated throughout the season, it’s important to make sure batteries are properly charged. An under-charged battery can perform well at 80°F, but its true condition becomes evident at 0°F when starting current demands can increase by 200 percent and a battery, even in great condition, is reduced to 40 percent of its summer cranking current.

Frequent starts and stops are also detrimental because the battery is never given the chance to fully recharge.

Utilizing the Undercarriage

The undercarriage of a machine represents roughly 40 to 60 percent of its maintenance costs over the machine’s service life. So in order to maximize a machine’s efficiency in the winter, proper undercarriage maintenance is essential.

Operators should make daily inspections and keep it clean of any mud, snow or debris. Carefully look for loose or worn parts, and refer to the operator’s manual for correct track tensioning and adjustment.

Whether operating the machine during the winter or storing it, make sure to schedule an undercarriage inspection once a year.

Taking Care of Tires

Tires require daily care and maintenance during winter. Because of this, it’s important for equipment operators to take steps to reduce tire wear while operating equipment.

For starters, always keep tires properly inflated, and remove counterweights when not in use, as they put additional stress on the tires. Look for even wear, remove debris, and inspect tires for any cracking and chunking. If the center of the tire is worn smooth, or there’s any chunking, then it’s time to replace them. A Successful Winter

In order to properly maintain equipment operating in cold temperatures and snowy conditions, operators should alter their operation habits to ensure equipment longevity. Behaviors like minimizing high operating speeds and on-road travel and alternating turning directions can be the difference between downtime and productivity.

Another important piece of maintenance is a pre-operation inspection and the proper warm-up of the equipment. Warming up the machine reduces shock to components caused by cold fluids or hydraulic systems. The potential for blown hoses or O-rings increases with colder weather. Providing sufficient warm-up time will provide an operator a more productive machine as well as increase safe operation and a more comfortable operating environment.

When it comes to operator behavior, excessive idling should be monitored closely, as it consumes needless fuel, warranty hours and contaminates diesel particulate filters. Condensation can build up in the crankcase, which promotes the build up of acids and sludge, leading to costly downtime and potential repairs. Also, if something does happen and business owners require replacement parts or fluids, remanufactured parts are a great option. Remanufactured parts, like the ones offered from CASE, are built to meet or exceed original OEM specifications, and are backed by a best-in-class warranty that in some cases is better than new warranty coverage.

Protecting your equipment during the winter is a smart investment in not only the equipment itself, but also your future.

Previous Article Construction Plant Fitter Apprenticeship at Pat O’Donnell & Co
Next Article Good luck to the Clare Hurlers in the GAA Senior Hurling Quarter Final this weekend!
Print
2291